What's thethe tensile strength of chain CC600 ?The minimum UTS of CC600 chain is 65 KN.But usually our CC600 chain can be reach 100 KN or more.

If zmie can produce the stainless steel drop forged chain?Sure, zmie make the high quality stainless steel drop forged chain.

How many models of 698 does zmie manufacture?ZMIE have two models, 698 chain and X698 chain.

What Color Can Zmie Make For The CC600 Chain? Natrual, white zinc plated, yellow galvanized and stainless steel for CC600 chain ...

Doze zime manufacture the F100 conveyor chain?Sure, zmie have the tooling of conveyor chain F100. ...

Two half trolleys and two nut & bolt assemblies are required to make a complete trolley assembly.

...

Pro ...

pin of drop forged chain Generally, the hardness of the pin of drop fogrg...

Usually there are two kinds of ZMIE enclosed track chain packing way for customer choices.One is packed into case directly, which is more economical, and another is 20FT in one box, 40boxes one pallet.

Low temperature will cause material brittleness. Lowest temperature of Martensitic stainless stell is -70℃。 Lowest temperature of Austenitic stainless steel is -100℃. Normal stainless steel chain using in the field with temperature above 400℃ will cause material heat fatigue, expansion, deformation, pitch accuracy loss and breaking load decrease significantly.

Our leading casting chains are CC600, 907E-51 and 4103 chain.The casting process determines the rough surface of the casting.It must be increase the gap between the pin and cast link to ensure the free rotation.The large gap causes the chain to elongate, which makes the casting chain have the theoretical pitch and the actual pitch.

ZMIE customers mostly are overhead conveyor system manufacturers or chain manufacturers, also end users all through the world.

Our quality control procedures include the following:1, Raw material analysis and check steel suppliers c...

Usually our trolley without any grease, because we are not sure our customer need which temperature greas...

...

Enclosed track chain How to design the curved rail radius of the enclosed...

smooth pin The Smooth pin has a smooth, uniform surface, with no flash.1,...

What’s the Loading Capacity Of 1 Pair Of Trolley?The loading capacity of 1 pair X348 trolley is 90kgsThe ...

Zmie have X-type, Regular Type and S-type forged chain.

How To Select Conveyor Chains? 1. Conveyor chains may break when an exce...

ZMIE can provide aerial chain with high qualit...

more popular ench 20FT in one box, and 40boxes one pallet. ...

CC600 chain Usually the most popular is NATURAL CC600 chain.And we also have stainless steel, zinc plated and yellow galvanized for customers choice. ...

How many pin type does zmie have Because pin easy to wear and tear, usually it made of material 42CrMo.ZMIE have standard pin, oil groove pin, smooth pin, extended pin and...

Frequency of lubrication is determined by many factors. Chain length and speed, heat and water are important considerations. A rule of thumb is for slow moving conveyors, low to moderate heat conditions, one lubrication cycle for each eight hour shift that the conveyor is operation. Example: A 500′ conveyor at 10′ per minute would make 9.6 revolutions in an eight hour period. Programing 9 into the...

Yes, zmie can fill high temperature grease in roller turn roller, which can work under 220℃.

Yes, all Zmie's overhead trolleys are with self-locking nuts.see attached photo.

The drive dogs the most importent part of the caterpillar drive chain, are made of 40Cr forging , then though hardened. If necessary, we will induction hardened for the head of drive dog.

There are a number of ways to reduce stretch or elongation in a chain application. Some of the ways are listed below:*Improve the lubrication itself and the process of applying the lube to the chain ensuring the lube is penetrating the pin/bushing area.*Choose a chain that has a higher hardness of the chain’s bushings and pins.*Select a chain where tension is reduced in the bearing area (the pin/b...

On enclosed track conveyors, typical lube time settings are around 10 to 15 milliseconds. Monorail and formed track conveyors require more because of the greater bearing surface to be covered, usually somewhere in the 15 to 25 millisecond range. Depending on various factors, these settings may be higher or lower, but it is not recommended to go below 8 milliseconds to insure proper solenoid operat...

Forging is metal that has been heated in order to soften it then pressed, hammered, or otherwise formed into a shape. All forgings begin as cast starting stock. Forgings benefit from the forming operation which enhances their overall toughness and fatigue resistance.

Drop forged conveyor chains are made from specially high grade alloy steels. In the following table, you can see the advantages of various kinds of materials.

Zmie's standard "H" attachment is the most widely used trolley attachment.The "H" attachment is a steel forging with 2 pieces suitable for almost any type of hook. 点击打开链接

The casting process determines the rough surface of the casting.It must be increase the gap between the pin an cast link to ensure the free rotation.The large gap causes the chain to elongate, which makes the casting chain have the theoretical pitch and the actual pitch

How to design the curved rail radius of the enclosed track chain?All horizontal turns are avialable in 24" and 36" radil and vertical curves illustrated .However, special radius turns can be fabricated upon request. For smaller than 24" radius, horizontal traction wheels can be furnished.

The chain 698H and 698 have the same pin, so the ultimate tensile strength is the same. If you need higher strength, better material is a good chice, for example, 4140 or 8640.

The outer diameter of X458 trolley is 59mm.If the distance between chain center to the wheel center doesn't change (100MM), then the wheel diameter can be changed as per the customer's request and don't need the extra mould cost.

The hardness of Zmie overhead conveyor chains are inner link & outer link :38-42HRCpin :40-44HRC

Yes, ZMIE can supply 90 degree indexing swivel hook type with detents at 90 degrees, which has a 125 lb capacity and is used on 3”I and 4”I systems.